HVAC Materials
Copper Pipe
Seamless copper tube used for sanitary drainage, waste and vent systems in plumbing applications is often referred to as "DWV" tube and is manufactured to the requirements of ASTM B 306 - Standard Specification forCopper Drainage Tube (DWV).
.jpg)
PIR Glue
Duct Sealant
EXCEL AIR’S 32-17-0 is a one component, highly qualified, lastic-elastic sealant based on an acrylic emulsion.
PVC Pipe Wrapping Tape
PVC Pipe Wrapping Tape composed of soft lm with rubber based PSA it is characterized by excellent insulation, good flame retardant properties and excellent resistant to low temperature.
WD 40
The long-term active ingredient is a non-volatile viscous oil which remains on the surface to which it is applied, giving lubrication and protection from moisture.
Welding Gas Tank
Consists of fuel gas and oxygen cylinders, each with a gas regulator for reducing cylinder pressure, hoses for conveying the gases to the torch, and a torch and tip combination for adjusting the gas mixtures and producing the desired flame
Duct Glue 81-10-0
A low cost, quick setting synthetic elastomer adhesive for use with fibrous glass insulation (up to 3 lbs./cu.ft.) duct wrap and acoustical linings for air handling ducts.
Foster 30-36
Foster 30-36 Sealfas Coating is a white, fire resistive, tough, washable, indoor coating for thermal insulation on ducts and piping when applied in 2 coats.
Refrigerant Cylinders
This colorless gas is better known as HCFC-22, or R-22. It is commonly used as a propellant and refrigerant.
Bolt , Washer & Nut
Designed to engage with the toolused to tighten them. Some bolt heads instead lock the bolt in place, so that it does not move and a tool is only needed for the nut end.
Self Drilling Screws
A preliminary drill-like fluted tip that looks much like the tip of a center drill. These screws combine a thrilling-like action and the fastener installation itself into only one driving motion.
Drill Bit Hilti Type
Designed with a full carbide head and unique head and helix design to drill faster than any other drill bits - in concrete, brick, masonry and more.
Unifix (Anchor Bolt)
Consist of a threaded end, to which a nut and washer can be attached for the external load. Can also be used to firmly affix embed plates to a concrete foundation when used with a structural steel element.
Fix Bolt (Anchor Bolt)
Consist of a threaded end, to which a nut and washer can be attached for the external load. Can also be used to firmly affix embed plates to a concrete foundation when used with a structural steel element.
Wall Plug (Fisher)
A fiber or plastic insert used to enable the attachment of a screw in material that is porous or brittle or that would otherwise not support the weight of the object attached with the screw. It is a type of anchor that, for example, allows screws to be fitted into masonry walls.
.jpg)
TCT Hole Saw
A saw blade of annular (ring) shape, whose annular kerf creates a hole in the workpiece without having to cut up the core material. It is used in a drill.
Electrical Insulation Tape
Pressure-sensitive tape used to insulate electrical wires and other materials that conduct electricity. It can be made of many plastics, but vinyl is most popular, as it stretches well and gives an effective and long lasting insulation.
Red Oxide Paint Primer
A preparatory coating put on materials before painting. Priming ensures better adhesion of paint to the surface, increases paint durability, and provides additional protection for the material being painted.
Paint Thinner 4L
A solvent used to thin oil-based paints or clean up after their use. Commercially, solvents labeled "Paint Thinner" are usually mineral spirits having a flash point at about 40 °C (104 °F), the same as some popular brands of charcoal starter.
PVC Pipe Adhesive
A clear solvent-based, high strength cement for PVC SCH 40, Types I and II, sewer and conduct PVC pipe through 4” in diameter, and PVC SCH 80 through 1 1/2” diameter. Approved for use in potable water and DWW systems.
Fast Steel Epoxy
A hand-kneadable, fast-setting, industrial-strength, steel-reinforced polymer compound for permanent repairs to anything made of steel or other metals.
Industrial Hand Gloves
Safety gloves are hand garments meant for the protection of the wrist, hand, fingers, and thumbs from adverse processes or conditions.
Copper Fittings
Cast copper alloy fittings used for drainage, waste , and vent applications with solder joints are manufactured to the requirements of ANSI/ASME B16.23 - CastCopper Alloy Solder Joint Drainage Fittings - DWV.
Cutting Disc Steel
Expendable tools used on angle grinders or stationary devices forcutting a variety of materials - from metal alloys (steel, stainless steel, aluminum), to wood, stone, concrete and other materials.
Measurement Tape
A flexible ruler used to measure distance. It consists of metal strip with linear-measurement markings. It is a common measuring tool.
Paint Brush
A brush used to apply paint or sometimes ink. A paintbrush is usually made by clamping the bristles to a handle with a ferrule.
Test Manifold
Regulates fluid flow between pumps and actuators and other components in a hydraulic system. It is like a switchboard in an electrical circuit because it lets the operator control how much fluid flows between which components of a hydraulic machinery.
Steel Cutting Scissor (Aviation Snips)
Compound-action snips are also known as aviation snips because they were developed to cut aluminum in the construction of aircraft. They can handle aluminium up to 18 gauge, mild steel up to 24 gauge or stainless steel up to 26 gauge.
Lockins Plies
Pliers that can be locked into position, using an over-center action. One side of the handle includes a bolt that is used to adjust the spacing of the jaws, the other side of the handle (especially in larger models) often includes a lever to push the two sides of the handles apart to unlock the pliers.
Rivit Gun
Pneumatic hammer, a type of tool used to drive rivets.
Cutter
The fixed or folding blade utility knife is popular for both indoor and outdoor use. One of the most popular types of workplace utility knife is the retractable or folding utility knife (also known as a Stanley knife, box cutter, X-Acto knife, or by various other names).
Stuck-up Pin
Stuck Up Pins are insulation hangers with a self adhesive sticking base. It is manufactured in order to fix insulation materials to smooth surfaces such as ducts.
