HVAC Materials

Copper Coil (Pipe)

Copper Pipe 

Seamless copper tube used for sanitary drainage, waste and vent systems in plumbing applications is often referred to as "DWV" tube and is manufactured to the requirements of ASTM B 306 - Standard Specification forCopper Drainage Tube (DWV).

PIR GLUE

PIR Glue 

Duct Sealant

Duct Sealant

EXCEL AIR’S 32-17-0 is a one component, highly qualified, lastic-elastic sealant based on an acrylic emulsion.

PVC Wrapping Tape

PVC Pipe Wrapping Tape

PVC Pipe Wrapping Tape composed of soft lm with rubber based PSA it is characterized by excellent insulation, good flame retardant properties and excellent resistant to low temperature. 

WD-40

WD 40

The long-term active ingredient is a non-volatile viscous oil which remains on the surface to which it is applied, giving lubrication and protection from moisture.

MAP GAS.jpg

Welding Gas Tank

Consists of fuel gas and oxygen cylinders, each with a gas regulator for reducing cylinder pressure, hoses for conveying the gases to the torch, and a torch and tip combination for adjusting the gas mixtures and producing the desired flame

Duct Glue 81-10

Duct Glue 81-10-0

A low cost, quick setting synthetic elastomer adhesive for use with fibrous glass insulation (up to 3 lbs./cu.ft.) duct wrap and acoustical linings for air handling ducts.

Foster Glue 30-36.jpg
Foster 30-36

Foster 30-36 Sealfas Coating is a white, fire resistive, tough, washable, indoor coating for thermal insulation on ducts and piping when applied in 2 coats.

R-22 Refrigerant Gas Cylinder.jpg
Refrigerant Cylinders

This colorless gas is better known as HCFC-22, or R-22. It is commonly used as a propellant and refrigerant. 

Bolt Nut Washer
Bolt , Washer & Nut

Designed to engage with the toolused to tighten them. Some bolt heads instead lock the bolt in place, so that it does not move and a tool is only needed for the nut end.

Self Drillimg Screw.jpg
Self Drilling Screws

A preliminary drill-like fluted tip that looks much like the tip of a center drill. These screws combine a thrilling-like action and the fastener installation itself into only one driving motion.

Drill Bit.jpg
Drill Bit Hilti Type

Designed with a full carbide head and unique head and helix design to drill faster than any other drill bits - in concrete, brick, masonry and more. 

Unifix Bolt
Unifix (Anchor Bolt)

Consist of a threaded end, to which a nut and washer can be attached for the external load. Can also be used to firmly affix embed plates to a concrete foundation when used with a structural steel element.

FIX BOLT.jpg
Fix Bolt (Anchor Bolt)

Consist of a threaded end, to which a nut and washer can be attached for the external load. Can also be used to firmly affix embed plates to a concrete foundation when used with a structural steel element.

WALL PLUG FISHER.jpg
Wall Plug (Fisher)

A fiber or plastic insert used to enable the attachment of a screw in material that is porous or brittle or that would otherwise not support the weight of the object attached with the screw. It is a type of anchor that, for example, allows screws to be fitted into masonry walls.

Hole Saw (TCT).jpg
TCT Hole Saw

A saw blade of annular (ring) shape, whose annular kerf creates a hole in the workpiece without having to cut up the core material. It is used in a drill.

ELECTRICAL TAPES.jpg
Electrical Insulation Tape

Pressure-sensitive tape used to insulate electrical wires and other materials that conduct electricity. It can be made of many plastics, but vinyl is most popular, as it stretches well and gives an effective and long lasting insulation. 

RED OXIDE PRIMER.jpg
Red Oxide Paint Primer

A preparatory coating put on materials before painting. Priming ensures better adhesion of paint to the surface, increases paint durability, and provides additional protection for the material being painted.

Paint Thinner.jpg
Paint Thinner 4L

A solvent used to thin oil-based paints or clean up after their use. Commercially, solvents labeled "Paint Thinner" are usually mineral spirits having a flash point at about 40 °C (104 °F), the same as some popular brands of charcoal starter. 

PVC Pipe Adhesive.jpg
PVC Pipe Adhesive

A clear solvent-based, high strength cement for PVC SCH 40, Types I and II, sewer and conduct PVC pipe through 4” in diameter, and PVC SCH 80 through 1 1/2” diameter. Approved for use in potable water and DWW systems.

STEEL EPOXY.jpg
Fast Steel Epoxy

A hand-kneadable, fast-setting, industrial-strength, steel-reinforced polymer compound for permanent repairs to anything made of steel or other metals.

HAND GLOVES.jpg
Industrial Hand Gloves

Safety gloves are hand garments meant for the protection of the wrist, hand, fingers, and thumbs from adverse processes or conditions. 

Copper Fittings
Copper Fittings

Cast copper alloy fittings used for drainage, waste , and vent applications with solder joints are manufactured to the requirements of ANSI/ASME B16.23 - CastCopper Alloy Solder Joint Drainage Fittings - DWV.

CUTTING DISC.jpg
Cutting Disc Steel

Expendable tools used on angle grinders or stationary devices forcutting a variety of materials - from metal alloys (steel, stainless steel, aluminum), to wood, stone, concrete and other materials.

MEASUREMENT TAPE.jpg
Measurement Tape

A flexible ruler used to measure distance. It consists of metal strip with linear-measurement markings. It is a common measuring tool.

PAINT BRUSH.png
Paint Brush

A brush used to apply paint or sometimes ink. A paintbrush is usually made by clamping the bristles to a handle with a ferrule.

TEST MANIFOLD.jpg
Test Manifold

Regulates fluid flow between pumps and actuators and other components in a hydraulic system. It is like a switchboard in an electrical circuit because it lets the operator control how much fluid flows between which components of a hydraulic machinery.

AVIATION SNIPS.jpg
Steel Cutting Scissor (Aviation Snips)

Compound-action snips are also known as aviation snips because they were developed to cut aluminum in the construction of aircraft. They can handle aluminium up to 18 gauge, mild steel up to 24 gauge or stainless steel up to 26 gauge.

LOCKING PLIER.jpg
Lockins Plies

Pliers that can be locked into position, using an over-center action. One side of the handle includes a bolt that is used to adjust the spacing of the jaws, the other side of the handle (especially in larger models) often includes a lever to push the two sides of the handles apart to unlock the pliers.

RIVIT GUN.jpg
Rivit Gun

 Pneumatic hammer, a type of tool used to drive rivets.

CUTTING KNIFE.jpg
Cutter

The fixed or folding blade utility knife is popular for both indoor and outdoor use. One of the most popular types of workplace utility knife is the retractable or folding utility knife (also known as a Stanley knife, box cutter, X-Acto knife, or by various other names).

STUCK UP pin.jpg
Stuck-up Pin

Stuck Up Pins are insulation hangers with a self adhesive sticking base. It is manufactured in order to fix insulation materials to smooth surfaces such as ducts.

Site Visits

  • Facebook - White Circle
  • LinkedIn - White Circle
  • Twitter - White Circle
  • Google+ - White Circle

Copyright 2020 | Excel Air Electromechanical WLL 

Web Designed by: jepenullar™

A length of tape or thin flexible metal, marked at graded intervals for measuring.